Nailers, or we can say the nail guns are the tools used to put nails in the wood or other objects. This tool has replaced the work of hammers screwdrivers and many other tools. Being a safer version, the tool is getting recognized. Companies are stepping high with production. New innovative ideas are being used. There is a lot of experiment with a tool that is going on. This article focuses on the angled nailers and straight nailers. This is an in-depth comparison of Angled vs Straight Nailers. If you are investing in one such tool, this is the one-stop solution. The article talks about the pros and cons of the tools.
Both the tools work well with any of the surfaces. The purchase of the tool depends upon the use. The straight nailer can be used in construction sites; also, this is an affordable option. This nailer works pretty well; the only drawback is it only works in one direction. The weight is a bit heavy. But you can easily work with the tool. An angular nailer is an advanced version. This has improved the technologies used. The design is sleek.
Angled Vs Straight Nailers: Comparison Table
|Specification||ANGLED NAILER||STRAIGHT NAILER|
|Weight of nail||16 gauge||15 gauge|
|Angle scale||21 to 34 degree||90 degree|
|Price||Check Price||Check Price|
Angled Vs Straight Nailers: Differences
- The main difference is the angle. One device works at any angle scale of 24 to 31 degrees. Other works only at 90 degrees. Which means you can work with tight spaces with one tool. Other works normally as hammer nail mechanism. So for precise use, the angled nailer is better.
- The other difference is the body of the tool. The straight nailer has a heavy built. In comparison, angled one is lighter in weight. Which means angled nailer can be used for a more extended period. At the same time, straight nailers can cause pain after working for some time.
- The angled nailer can take a 16 gauge nail. A straight nailer can take 15 gauge nails. This means angled nailer provides stronger uphold capacity. Straight nailers can be a little weak for this.
- The versatility of the angled nailer is more than the straight nailer as it can work in tight spaces. In comparison, straight nailer has a limit to perform. The angled nailer has a large field of work. In contrast to straight nailer angled nailer wins here.
- The major differce3 is the cost of the tool. Angled nailer is way more expensive, whereas straight nailer is affordable. There is an investment of money on the tool. This makes straight nailer wins the task. As for a nailer, spending more money sounds silly.
- The nails off angled machines are expensive. The straight machine has less expensive nails and better quality too. The same verdict putting a lot of money on nail sounds silly. But it works magically on the surface.
- The availability of the nails of an angled nailer is difficult. They are expensive too. They are difficult to find. Straight nailers’ nails are easily available in the market. You can search for them.
- Being lighter in weight, it is easy to take angled nailer anywhere you want. This can be used in different places at different times.
- Angled nailer comes with a long nose; this helps in reaching the tighter spots. Whereas the straight nailer as a small nose which restricts the area coverage. So working with an angled nailer, one can reach corners of the joints.
- Angled nailer is an advanced version of a straight nailer. There are many add on to the tools done over a while. It comes with a bit advanced mechanism.
Angled Vs Straight Nailers: What Is It?
The angled nailer is the precession tool. This tool works effectively on the narrow surfaces. The magazine of this nailer is angled, so the nails don’t come in the way. This can take up to 16 gauge nails. The nails are thicker than the regular nails. This tool has a stronger upholding power. This means more stable and durable the nails last. This works best with nooks and corners. Angle scale can go from 21 degrees to 34 degrees, depending on the space. This is a precision tool.
The straight nailer is the basic nailer. This work normally like a hammer and nail thing. The magazine of this nail is not angled. This works in a 90-degree position. This can take up to 15 gauge nails. This also has good upholding. If compared to an angled nailer, the upholding is a bit lacking. This works great on the surface. You can also see the comparison with other types of nailers.
Angled Vs Straight Nailers: Pro and Cons
Pro– Talking about the tool it is a lightweight tool. This will be easy to work with. People can work for a longer time. As said, it works in an angle so one can cover corners and to the narrow spots. This is easy to handle. It has a stronger upholding capacity. This tool can take 16 thick gauge nails. The nailhead used with this is’d”. This tool can be used for a more extended time. This one is a low maintenance tool. This comes with a long nose. This gives a broader area to perform. This is a small tool. This can be taken anywhere.
Cons– The nails used by the tool are rare. This makes them expensive to buy. The tool itself is costly. This is an investment tool. The primary issue with the device is its price. Also, non-availability makes another point. This also cannot give extra support to narrow surfaces. So this can make them flimsy. The surface can break as it gets weak.
Conclusion– If you have a reasonable budget, you can invest in this tool. This tool works perfectly on any surface. Well, get into tight spaces. It is portable. The weight is less can work for hours. It is an investment tool. It is a heavy-duty tool. The body material is good. This will last you forever.
Pro– Talking about this device is a simple tool, as explained. The tool works at a 90-degree angle. This is good for square nails. The device doesn’t leave any marks on the surface caused by the drilling of the machine. This is a clean way to work with a tool. This tool is right for short construction work. This tool is suitable for framing work. This drills small nail hole so easy to hide. The machine is less expensive. The tool is Budget-friendly. The body of the tool is heavy-duty.
Cons– Talking about cons, this tool works only at 90 degrees. This doesn’t cover the tight spaces. They do not work precisely. The work field is smaller as compared to the angled one. Another con of the tool is its weight. This is a bulky little machine. This tends to make it a little challenging to work with. You can’t work for a long time. Excessive work can cause pain in the hands and shoulders. So it restrains working hours. This machine has less holding power compared to angle one. Also, this is a less versatile machine. This works only at an angle of 90 degrees.
Conclusion– if you are in search of a simple nail gun that performs the simple task, you can go for this. This is a budget-friendly machine. The nails are easily available; they are less expensive. The body of the tool is heavy. So if you can work with a heavy machine, you can buy this. This also is easily available. The tool is low maintenance. Working is easy to understand. One can easily use the machine.
Working for a long time can cause pain as it is heavy. Also, long work periods are no for this tool. This is good for framework and construction as it fixes the nail well. Also, the marks are less visible due to a small head.so in all this is a straightforward machine. This works the same likes a hammer and nail in a mechanic form.
Angled Vs Straight Nailers: Similarities
- Both the machines come with the corded and uncorded system. You can buy any version of the machine. Both can be portable in use. You can take both anywhere and work with them.
- Another similarity between them is the usage power both work with the same backdrop of power, but the purpose of both the machine is different. Also see the comparison between brad and finish nailer.
Q. Which one can be used for tight space?
Q. Which tool is inexpensive?
Q. What is the nail size of the angular nailer?
Q. Which one is a better buy?
Q. Nail size use by straight nailer?
If you want to work in a corner or tight space straight, one is a good option. As said above, the purpose decides the purchase. If you are working in a construction field or working with frames, you can go for straight nailer as it is easily affordable, durable, and hassle-free to use. But if you are working in tight space like drawers cupboards or any space where you need an angle, you can go for an angular nailer. As told above, the angle scale is 24 to 31 degrees.
It easily gets inside the spaces and does the job. The only major drawback is the price of the device. The availability of nails in the market is also an issue. So there are drawbacks in both the tools. You have to decide according to your choices. Both tools excel in their field of work. It just depends on the work you have to do using the tool. Before purchasing, make sure to see the usage. Read the article so that you can make the right decision before buying investing in the device. Make sure you go through the information about the tool before buying the tools.
Even if the hammer nail mechanism is getting replaced by theses tool, the safety is essential. Before using the tool, it makes sure you wear protective glasses. This will cover your eyes and won’t let any dust particles to enter in your eyes. You should wear gloves before working with the tool. No matter how safe the tool is to use, always wear gloves. Always make sure before Working with the tool you see the device is on or off, it may happen you leave it on. This can cause serious injuries.