Guess you have wondered if baseboard corners can be cut without using a miter saw. There is a possibility, but you need to follow the art of proper alignment correctly. The baseboard angle and joint alignments should match the floor and walls. If you wish to cut as per precise angle or basic molding of joints, a regular circular saw, jigsaw or a handsaw can enable you pieces required for molding. Hence, you can use multiple tools instead of a miter saw. So here are the steps on how to cut baseboard corners without a miter saw.
Contents
How To Cut Baseboard Corners Without A Miter Saw – Step By Step Guide
Here we will guide you through different ways to cut baseboards. For cutting without using the miter box:
Total Time: 1 Hour
Step 1
Make for nail holes at each corner-block of the trim piece with the help of a pivot bit. Two holes see-through on either side should be produced at each corner. Be careful to drill the holes; their positions must not be close.
Step 2
Place the drilled block at the corner of the room. To check whether the block is straightly aligned better, use a level. For stability, you need to hammer nails to the side walls.
Step 3
Mount such corner block at each corner of the room. Use a nail set to sink the nails implanted.
Step 4
You should trim the larger side of the block. To achieve this, you should use tape and pencil to mark the precise end-to-end dimension of blocks.
Step 5
For straight lines cross the trim, a perfect square needs to be formed. Use a tri square for the purpose.
You are supposed to put the trim blocks between the corner blocks. But make sure that the square ends produced, i.e., the trim should be facing each other. Subsequently, pilot holes at every fifteen inches need to be drilled at both the top and bottom positions of the trim edges.
Step 8
The finish nails have to be hammered in place. Use a nail set to sink the heads below the support. Now, you need to repeat the same process at every corner.
Coped Joint Creation
Step 1
In this method, to tightly fit the corner of wall pieces for molding need to be cut at ninety degrees. These pieces need to be fixed on the walls either by hammering or using nail guns.
Step 2
You cut the second piece as per the measurement, which should be from wall to wall surface. You should cut the edge to forty-five degrees to cope up. The back-side of the mold should be cut, disallowing anybody to view it from the front. You are required to hold the saw at an angle to suit.
Step 3
Finally, you should try the fitting of the coped piece along with the already mounted mold. For fine-tuning and producing crisp edges at the butt, the coping saw can be used. Remember, you should never file a coped edge straight.
Step By Step Hand Saw Used For Cutting
Step 1
Cutting a baseboard isn’t troublesome if you don’t possess a circular saw. A hand saw along with a miter box can do the job. It is vital to get straight wart free wood for the purpose. You are recommended to cut two twelve inch pieces from 1×6 lumber or 1X4 lumber. Fir and oak tree woods would be perfect.
Step 2
Use wood glue along all sides of the 1×4 lumber pieces and lay it on a flat table. Nest on each side places the 1×6 lumber pieces vertical—drill screws of ½” diameter to join 1×6 and 1×4 pieces together. In the end, you will get a four-inch box that would be open.
Step 3
Use slope to mark 45⁰ at the top edge of the box
Step 4
The hand saw has to be aligned at 45⁰ as per the marks on the top side of the box. You should ensure the handle of the saw remains perpendicular to the mark.
Step 5
The ultimate step will be to cut the baseboard using the hand saw and box. Hold the baseboard firmly against the side of the box. As per the kerf dimension, the baseboard needs to be cut based on the mark on the box.
Things You Would Need
A Measuring Tape
To get the actual wall to wall dimensions to work with precision measuring tapes can help. Use measuring tapes and appear with molds or wooden blocks.
A Level Gauge
A level gauge is essential to identify if the wooden block is installed straight. Whether it’s a small or more extended wooden block, level gauges would enable a decent, straightforward setting.
A Pencil For Marking
To mark the cutting piece from baseboard corners, you utilize the pencil. Also, a pen can be used on sidewalls to maintain a proper level. Pens are frequently used for markup options.
A Hack Saw Or Miter Box
For cutting baseboard corners, if you are not using a miter saw, a hack saw and a miter box can allow you to cut pieces. So, in the absence of a miter saw, a hack saw can provide a corner trim.
Few Finish nails
Once the benchmarks for the setting of wooden blocks are ready, Fresh nails need to be hammered at the top and bottom of the piece. Using a nail sent, you can sink the nail head downwards. Keep the same stock for other corner baseboards also.
A Hammer Or Nail Gun
To dig holes on walls to facilitate nails or screws to fit, a hammer or nail gun must be used.
A File (Optional)
The miter saws are more effective in producing smooth edges. But other tools are not capable of producing such a finish. A circular saw is useful in cutting waste at corners, but the finish is not that perfect. So filing is needed. It is unwanted to use files, though.
A Nail Set
The accessory meant for sinking the nails downwards, a handy accessory to use. They are convenient for nurturing the nails aesthetically as well.
FAQs
1. What are miter saws used for?
If you want a detailed woodcut, miter saws are apt. When cutting 2x4s or other wood pieces, the miter saw gives a perfect angle and measurements.
2. Is the miter saw dangerous to use?
It isn’t dangerous if you are following all safety regulations and grasp operation manuals thoroughly.
3. What criteria for miter saws need to be considered?
The miter saws are meant for clean finish cutting. Blades with 80 teeth are best suited. The selection of the blade is essential. Woodworks and plastics can be attended, but metals cannot.
4. How is it possible to cut skirting without using a miter saw?
It would be better to opt for a straight cut for this purpose. You need a square to ensure a straight cut. All you need is a saw and a pencil.
5. What angle is preferred to trim baseboard corners?
The various types of power saws available are a) circular saw, b) jigsaw, c) band saw, d) miter saw, etc.
7. What is the technique to cut baseboards without dismantling from the wall?
The baseboard needs to be scored with a sharp knife along the mark. A chisel needs to be inserted in the groove. Use a hammer to tap lightly from top to bottom. Next, use a flat board and hammer to get rid of the cut portion.
8. What are the best hand saw to cut molds?
For cutting molds, handsaws must have sharp teethed blades. In doing so, the Japanese styled pull saw, and the backsaws are found suitable.
9. Which saw is right to buy for beginners?
The best would be a jigsaw. Besides being a great media to create curves and shapes, they also provide straight cutting opportunities. The jigsaw suppresses circular saws in respect of performing.
10. Which would be a better option to buy, a circular saw or a miter saw?
Among the two options, a circular saw is much more versatile. But the cross cuts trims or producing finer angles, and a miter saw is better. Buying a circular saw would be wise.
Final Thoughts
A miter saw produces precise cutting of baseboards. But the use of miter saws needs more deliberation. Instead, a circular saw can perform corner trimming sufficiently. Jigsaws and various other hand saws can serve the purpose. So study instructions and technical features of tools before investing. Better opt for versatile a tool that makes your home development much easier. A single tool can perform the same as others with small adjustments.
Leave a Reply