You may need to cut and trim many baseboards for any project, so here we will help you to do it in a very efficient way. If you follow our step by step guide, then you will find the whole process significantly simpler. The process is more straightforward. The wrong direction in doing it makes it more challenging.
So, you can learn how to use a miter saw for cutting baseboards with our simple step by step guide. You are also expected to look into all the special tips given below. This will increase the efficiency of your work. Moreover, you can pair up all these small steps with any good tutorial. But be wise while choosing such tutorials. Don’t just pick up whatever you got at first search.
Recommended Miter Saw For Cutting Baseboards
How To Use A Miter Saw For Cutting The Baseboards – Step By Step Guide
Yeah, you have made your mind to proceed further in the steps. Here, we will give you the best overview. We are breaking the whole process of cutting a baseboard using a miter saw into small little chunks. You can call them as modules. It will guide you throughout the process stepwise. So, let’s dive into the article without much delay!
The steps are mentioned below, and you can follow them along with us:
Total Time: 30 Mins
Step 1: Taking Up Of Measurements
All the perfections are dependent upon your measurements that you will make. So, the primary step that you have to do before all other things is the measurement taken. To cut your baseboard with perfection by using a miter saw, you should measure your walls accordingly. You can do this by taking a measuring tape. If you don’t have one, then you can buy it from any ordinary shop. It is readily available. To get an exact measurement, measure all the walls either twice or thrice.
You have to cut it once, so if any mistake is there in the measurement, it will act as a real blunder. So, patiently measure all the sides and other things minimum twice. Otherwise, it will be merely wastage of your workpiece and your time.
Using a measuring tape, measure the length of the wall at the base from both sides. Don’t forget to measure all the walls. This will determine the dimensions of the baseboard you need.
During this step itself, you can use your stud tester. Test the location of electric wires or pipes, if any. This will help you a lot and save your time in upcoming steps. You are going to attach the studs to your baseboard also—Mark all the essential things while measuring something or finding something.
Step 2: Corner Cuts In The Inside Part
Now, after the first step, you should know about the corner cuts. As you have four walls, you need four corner cuts. And you have to make these four corner cuts in the inside part. This you can easily do with the help of your miter saw. But remember that here you need to align the bevel and saw off your miter to a specific angle. You need to fix your bevel at an angle of 45 degrees, and you saw at 0 degrees. This should be done with complete attention.
Now, use a pencil or a marker to mark the base part of your baseboard. This will help you to continue the cutting of your baseboard with a perfect follow up. Now, before turning on the saw, check the angles of bevel and saw. If they are aligned accurately, place the baseboard on your cutting surface.
Now, you can turn on the miter saw to start the cutting process. You can hold the handle of your miter saw using your one hand. On the other hand, hold the baseboard tightly so that it doesn’t move from its place. Now, complete the cut properly and push the blade gently. Don’t apply too much pressure.
Step 3: Corner Cuts In The Outside Part
In this step, you need not change any settings of your miter saw. Keep all the bevel and saw setting as it is. The saw is at 0 degrees, and the bevel is at 45 degrees. Retake your marking tool and mark the baseboard correctly. Now that you have made all the markings and measurements cut the baseboard. Note that the front side of the baseboard should be longer compared to the backside.
This will help you in joining the corners when you will complete the cutting process. Always remember that you should do all these steps very patiently and calmly. Do not hurry up without any attention. Try to be focused while measuring and marking. Most importantly, do not apply too much pressure. This will otherwise create a wrong impact on the miter saw.
Step 4: Cuts Of Square Type
So, by following the above steps, you will make the inside and outside corner cuts. It was not that difficult if you will do it with care. After that, we come to this step. After cutting your baseboard, you can think of joining them squarely. As you can see the heading of this step, it is all about cutting the square cut. If you want to eliminate the creation of angled baseboard with some random angles, you can go for this step.
Instead of making some alignment with your baseboards, you can be squarely joining them. Here, you don’t need any other inclinations. And this is the simplest way that we can use to join any two baseboards. You are always free to choose different kinds of more straightforward ways like perpendicular joint and straight joints. Both the square joint and the perpendicular joint are possible with the help of just a miter saw.
To have such type of joint, change the alignment of bevel and saw. Keep the bevel at 0 degrees and the saw at 90 degrees. This is opposite to the previous alignment. This will help you to make an ordinary cross-cut. And you are going to make your square joint-most quickly.
Step 5: Installing The Baseboard
Now, you have prepared your baseboard with all the necessary things. It might have taken some time to reach this step if you are going along with us practically. Though it was tiring, follow up this step also along with the other previous step. If you perform all the steps together, then it will take a little less time than doing it alone. Installing baseboard is the easiest step amongst all other steps. Here, you need to place your baseboard to the location where you want them to be permanent.
There should be proper orientation and matching up of the location and the baseboard. You can check for the proper place by keeping the baseboard temporarily. When you find the right location, then you start screwing up and nailing your baseboard. Install it permanently now. Attach the baseboards with the stud finders.
The nails you will use for the permanent placing of the board should be of 2 inches if you are using screws in place of nails.
Then you can have screws of around 1.5 inches. The lengths of nails and screws should not be too long because there may be some other electrical devices on the wall. Always keep yourself safe until the end of this work. Take all the safety measures, especially for your face parts and upper body parts.
Things You Would Need
- A miter saw
- A workpiece that you want to cut, i.e., baseboard
- A stud finder
- Safety goggles
- A pair of sharp blades
- Ear protectives
- Keep yourself in a safer environment.
- A miter saw is a very strong and powerful saw, so you need to control it properly.
- Wear protective glasses and ear protective to protect yourself from unwanted dust particles.
- Don’t wear gloves while handling a miter saw. Wearing gloves can reduce the grip of your hand with the miter saw.
- Be cautious of the circular blade of the miter saw.
- Power off the saw when not in use.
- Don’t start your saw before placing it rightly on the workpiece.
- Protect your hair from going near the saw. Tie them up if you have long hair.
- Hold the saw firmly and with full grip.
1. Is there any harm in wearing gloves to protect our hands while working?
It is good that you want to keep yourself safe. But wearing gloves is not a good option. This will hinder your perfect grip with the saw, and you will not control the saw properly.
2. What is the use of a stud finder in this process?
A stud finder is handy for all kinds of cutting and drilling processes. This will prevent you from cutting the workpiece from the wrong location. It tells you the presence of any electrical wires or types of equipment, if any. It is a good practice to use this for the testing before you start your cutting process.
3. Which type of miter saw is useful for baseboard miter joints, which are taller?
For such taller baseboard miter joints, a compound miter saw will be the best option. You can use any other ordinary miter saw also. But if you want to get a good finish in your work with taller joints, then using a regular saw will not work. If possible, then go for the compound miter saw.
4. How important is it to keep the miter saw at 90 degrees angle with the workpiece?
It is always advised to keep the saw blade precisely 90 degrees with the workpiece. This will ensure the required depth and angle of cutting. If you place it any other acute or obtuse angle, then the cutting will not be uneven. So, before cutting, make sure that you are holding your saw perpendicular to the cutting edge of your baseboard.
5. Which is the best miter saw to work with both the broader and longer workpiece?
We have three types of miter saw. For a wider workpiece, you should go for a sliding miter saw, and for the longer workpiece, you should use a compound miter saw. But if you have a workpiece which is both longer and wider, then go for the hybrid miter saw. It is also called a sliding compound miter saw. It has combined features of both the miter saws.
We hope that you got an immense amount of help from this article. Doing a task perfectly needs a good guide or process that can guide you in each step. If you followed all the steps provided in the article, then you should be able to improve your cutting skills using a miter saw. This will help you to do your work very quickly. If you are not confident still, then practice it till you feel confident in doing this.
Even if you have not thought of doing this task by yourself, I hope that you will think about it now. It is not that tough for waiting for someone else to do it. We can do it by ourselves. If you have learned it properly, then you can even train other people also. With this, you will finish your work in no time. According to us, you will get much more benefit if you pair up each step with some good online tutorials.
But remember that you should always have some written guide with you. This will help you to know some of the tips and tricks that are not provided in online tutorials generally. I hope to see you back with another article!